Without the plastic, you’ll lose a lot of water when it splashes onto the rocks. The plastic will catch and funnel more water than the rocks alone could. Then disguise the plastic with rocks, so that it won’t be visible in the pond. Extend one end of the plastic up to the top of the plastic pot, while tucking the other over the lip of the preformed pond liner and down into the water. It should be hidden at the center of your rock work.Īfter laying a first course of rocks in the front, cover them with a sheet of black plastic. The pot, and the tubing inside, won’t show when you’re finished. The pot will protect the tubing while you lay rocks all around it. You could easily substitute something else that might work better and can use either a Terra cotta pot or a plastic one. The pot functions as housing for the tubing within the cascading structure for the waterfall. Speaking of the flower pot, you’ll need that ceramic pot about 11 inches high and with a drainage hole in the bottom that’s big enough to fit the diameter of your tubing. It also gives you the leeway that you need, since you won’t know exactly from what height you’ll want the water to fall until you’ve finished laying the rocks. This will keep the tubing free, so that you can slide it through the pot up or down, at will. Make a small trench in the rock walls for the tubing to sit in under the rocks, so that the rocks won’t smash the tubing. You’ll essentially be building four mini rock walls around the pond. Their raised edges will help keep the water from deviating where you don’t want it go, namely, behind the rocks. The natural channel in such rocks will be very advantageous for the creation of the spillways in your cascade design. Occasionally, you’ll find rocks that curl up ever so slightly at the edges, leaving a depression in the middle. In addition to seeking out relatively flat rocks with sharp edges, see if you can find rocks that are slightly concave or cupped. How you lay the spillway rocks is also important. Try to choose rocks that are most likely to channel the falling water in the precise direction in which you want it to go. When rocks have blunt, gently-curving edges, some of the water tends to follow that curve and trickle back under the rocks. They should also have sharp, squared edges water will cascade more cleanly over sharp edges. The spillway rocks should be relatively flat as opposed to rocks that are more rounded in shape. These are the rocks that will make up the waterfall itself. The most important rocks are what might be termed the “spillway” rocks. Now, it’s time to move on to the structure itself. If your carpenter’s level is showing that the bottom of the hole (where the sand is) is not level, then remove the preformed liner from the hole and rake the sand until it is level. Make sure it is level - front to back, and left to right. Next, place the preformed liner into the hole for the backyard pond. Rake the sand to get the level of the preformed liner just right. That will reduce the amount of dirt that will fall into your pond. Put about an inch of sand at the bottom of the hole, so that the top rim of the preformed liner will stand about an inch above ground level. Sand will also be used at the bottom of the hole, because sand floors provide the stability needed to play with the height of preformed liners. If you find the hole you’re digging is a little bigger than the liner, just fill in the sides with sand. The depth of the hole should be the same depth as the liner and the diameter as close to the actual diameter of the liner as possible to ensure a nice, snug fit. (Mark the outline with flour or white spray paint.) Then start digging! Simply invert the liner and trace around it on the ground. Then measure the liner you have chosen so you can dig a hole big enough to hold it. Remove all weeds in the area where you will be digging your pond. If you don’t have an outdoor outlet, one will have to be installed by a certified electrician. Ideally, the the waterfall should be located close to a patio, deck, or porch. Your backyard waterfall will run on electricity, so it will need to have its own outlet for a power source. Large ceramic flower pot (or similar) to house tubing about 11 inches tall.Tubing to run from pump to top of waterfall.Most of these can be found at hardware stores or discount DIY stores, like Lowe’s or Home Depot. We’re big fans of the backyard waterfall garden, so here’s a step-by-step guide to building your own waterfall right in your own backyard!īusy? Pin this to your Pinterest board for later.įirst, gather your supplies. The process isn’t very difficult and can be achieved with little expense. You can easily build your own backyard waterfall to add interest to your yard.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |